ပြင်ပ clamp flowmeter အတွက် တပ်ဆင်ခြင်းလမ်းညွှန် မြန်မာ

Step 1: Inspect Flow Of Water Direction

Check the flow direction for the fluid (liquid or gas) of your pipe before you install the ဒစ်ဂျစ်တယ်စီးဆင်းမှုမီတာ. This is extremely important as if you install the flow meter in reverse then it will not function as it should. If you're not sure about the flow direction, look for arrows printed on the pipe or volumes treating with one that is familiar with the system.

Step 2: Clean the Pipe

Then clean the place of pipe where the flowmeter will be placed. Scanning is itself a key step as dirt, dust or debris may lead to inaccurate measurements being taken. Wipe around the area nicely with cloth or a brush as you have to keep it clean. This will assist with the more efficient working of flowmeter.

Step 3: Attach the Flowmeter

Now, it’s time to connect the flowmeter to the pipe. Carefully encircle the flowmeter around the pipe(s) and press the screws to fasten. It is extremely crucial to ensure the placement of your flowmeter and that it remains stationary after you tighten it. It cannot give you accurate readings even if it is not in the right position.

အဆင့် 4: ဝါယာကြိုးများကိုချိတ်ဆက်ပါ။

Step 5: Connect wires to flowmeter The installation is complete! These wires are crucial as they transmit information to a control system that oversees the movement of the liquid or gas. Hope you pluged them right, else they wont work. Great! You are working with data as of October 2023.

Correct Flowmeter Installation Guide

To ensure that you obtain the best and most precise measurements from your အပူစီးဆင်းမှုမီတာ, check out the following information:

မှန်ကန်သောအရွယ်အစားကိုရွေးချယ်ပါ။

Flowmeters by WIBAO need to be sized correctly for the pipe in which they are to be used. In case the flowmeter is small, it will not furnish accurate reading. However, if it is too big it could be too expensive and would not fit properly on your pipe. Always check the size prior to purchasing!

Install in the Right Place

This flowmeter should be installed in the straight pipe. This needs to be in the area where the fluid moves continuously. The flow provide for a constant flow to provide accurate measurement on your flowmeter. Never install it at turns or curves of the pipe.

Align it Correctly

You have to make sure that the flowmeter is correctly aligned with the direction of flow. A flow rate sensor is a thing that, if it's on the wrong way it won't measure it right. Don't bolt anything down until you are completely sure you are aligned.

Simple Guide to Installation of a Clamp Flowmeter

It may seem overwhelming to install a clamp flowmeter, and it's confusing enough that we made a simple, easy-to-follow guide for you:

Firstly ensure that the direction of flow of liquid or gas in your pipe This is an important step!

Then use the wire brush to clean the part of the pipe where you will be installing the flowmeter. 

These are some helpful tips to ensure that your အောက်ဆီဂျင်စီးဆင်းမှုမီတာ is functioning properly and providing accurate measurements:

Select your flowmeter to be the correct size for your pipe to give accurate readings.

For the use of this flowmeter, spot it within a directly length of tubing wherever the liquid or gas is flowing freely.

Check whether the Flow meter direction placed appropriately according to the flow direction.

Just make sure the pipe is clean before you put the flowmeter in to prevent issues.

And, finally, we will tighten the screws well so that our flowmeter can not move from its place.

Make sure that the wires are connected, and data can be sent.